Vea

contact

clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
clicca qui
                 
home page Versione italiana English version contattaci
home page Versione italiana English version contattaci

USB OPTOISOLATED I/O + HARDWARE KEY + STROBO LED PILOT

MICROBOARD USB TTL I/O + HARDWARE KEY

Contacts

I/O devices for industrial and scientific uses, flexible and cheap.
These devices have hardware key capability.
High speed and high current I/O for piloting LED in strobe mode.
Nominal current for each output: 1,5 A.

In strobe mode, the device can pilots LED lamp till 30V and 10A (SH version)

 
Vea S.r.l.
tel. +390331402751
fax. +390331401327
mail.vea@vea.it
 
   

 

HCE-IOV-102

  • dimension 70 x 91 x h 63 mm
  • for DIN bar
  • plug and play
  • optoisolated up to 2500V
  • power supply: 24V (range: 12V - 30V)
  • 8 PNP optoisolated input with signal LED
  • 8 PNP optoisolated output (from 1500mA) with signal LED
  • surge protection with signal LED, exclusion of the overloaded output and auto reset
  • response timing: less than 0.1 mSecs (0.005 mSecs for HCE-IOV-102-S)
  • two integrated programmable hardware keys in order to protect Your software on PC (one configurable key and the other customized on demand)
  • the inputs can be set as interrupts
  • functions: timer in mSecs, reading and writing of numbers
  • HCE-IOV-102-S version can pilots LED in strobo mode with pulses up to 10A 30V. The duration of these pulses is 0.005mSecs but it can be increased with steps of microSecs. The pulses can be sync with a command or an external input.
  • no special library, it is seen by PC as a normal serial port (115200 baud)
  • High current for each output (ver.L=1,5A; ver.S=3A; ver.SH=6A)
  • no internal PC board needed
  • no multiwire cable that goes from the PC card to the terminal bloc
  • no additional terminal block needed
  • the device needs only a standard USB wire for PC connection
  • excellent price/performance ratio

    depliant, driver, service manual
 

HCE-IOV-201

  • very compact device (only 54,7 x 24,2 x h 7,5 mm)
  • the device needs only a standard USB wire for PC connection
  • plug and play
  • self-powered by 5V USB connection
  • 8 TTL Inputs
  • 8 TTL Outputs
  • expandible with additional devices
  • Input and output response time lower than 0,25 mSec
  • programmable input filter from 0,25 mSecs to 250 mSecs
  • two integrated programmable hardware keys in order to protect Your software on PC (one configurable key and the other customized on demand)
  • the inputs can be set as interrupts, each one can be sets indipendently
  • functions: timer in mSecs, reading and writing of numbers
  • no special library, it is seen by PC as a normal serial port (115200 baud)
  • dimension 54,7(without usb connector) x 24,2 x h 7,5 (13,5 with pin connector) mm
  • programmable like HCE-IOV-101

    driver, service manual
 

PRICES:


"HCE-IOV-102-L": 180 € + IVA

"HCE-IOV-102-S" LED strobe mode (3A in contunuous): 240 € + IVA

"HCE-IOV-102-SH" High power LED stobe mode (6A in contunuous) : 290 € + IVA

"HAC-IOV-180" USB cable from PC to HCE-IOV-102/201 length 180 cm with double ferrite shield: 6€ + IVA

"HCE-IOV-201": 64 € + IVA

contact us for more info

 

made in Italy, buy italian please

we make custom modules and customize the firmware

Specifications are subjected to changes without notice

VEA s.r.l. - via Fratelli Rosselli, 43 - 20010 CANEGRATE (MI) - ITALY - e-mail: vea@vea.it - 2000-2014© All Rights Reserved - P.I. 13478090155